011 - 47374737 (100 Lines)
0item(s)

You have no items in your shopping cart.

Product was successfully added to your shopping cart.

Overview INNOVATIONTRUSTDEVELOPMENT

Com-Paint Touchup Spray Paint is very easy to use and even a novice can do wonders even in the First Shot. Just grab the Value Pack or a Can and say Bye to Scratches!!

The way to a good touchup job is to ensure first that the surface is clean and evened out for best results. Kindly go through the next section to understand the process. In case of any problems, you can see our FAQ section or write to us at sales@com-paint.com. Our team members would be happy to assist you at any stage..


How To Use

Application Instructions for Com-Paint Value Pack Kit.


What’s in the Value Pack Kit?

Your Com-Paint Value Pack Kit contains the following items:

  • Com-Paint Paint Can (Red Coloured Can) in yourpurchased shade
  • Com-Merge Can - Finishing Solvent Spray
  • Com-Cut Tube - Paint Cleaner / smoother
  • Com-Fill - Body Filler Paste
  • Com-Paint Emery Pad 400 and 2500 Grit
  • Com-Paint Rubber Applicator

The final result of the touchup depends upon the application procedure of Com-Paint Touchup Spray Paint. The result may vary due to many factors such as atmospheric conditions, type of surface etc.

We are enlisting below a specific procedure for applying Com-Paint Touchup Spray Paint that would give best results if properly followed.


Directions:

Check Colour: Before using, compare colour of the paint with the finish on your car / surface by spraying Com-Paint on a remote area, say on Car door sill.

Prepare Surface: Wash scratched area, remove any loose rust, old paint, dirt, wax polish etc. and dry the area thoroughly. Before spray paint application, it is important that you mask the area of your car which is to be refinished. The use of masking tape with even newspaper will help prevent over spray from reaching the other areas of the car.

For small and minor scratches: Wet emery pad EP - 2500 and the scratched surface. Gently rub back and forth on the scratch and across by applying a little even pressure of hand. Repeat until most of the scratch disappears. The area will become smooth and dull. When the surface area looks uniform, wipe dry with a clean cloth and now, it is ready for use of Com-Paint spray.

For Deep Scratches & Stone Chips: In case of exposed metal surface or deep scratches, use Com-Fill paste to fill the scratch. Apply light coats with the help of rubber applicator to spread evenly for a uniform fill of the scratch and level other surface imperfection. Immediately scrap off the excess with the rubber applicator to level the surface and let it dry for 30 minutes. Wet emery pad EP - 400 and the filled surface, gently rub by applying uniform pressure to level the area to be touched up with the adjoining surface. Wipe dry with a clean cloth and the area is ready for paint spray application.

Shake Com-Paint can vigorously until Agitator Ball moves freely. Hold Can straight 25 cms (12”) from the surface. Spray in stroking motion to avoid dripping. Apply light coats rather a heavy one which might make paint to sag & run. Wait for 5 minutes between coats.

Immediately, after completion of spray paint application, spray Com-Merge - Finishing Solvent on the outer periphery of the touched up area in order to let the paint overspray re-dissolve and merge with the surrounding surface. Let the touched up area dry for 72 hrs. for full curing of the paint film.

Clean paint spray button after use. If spray button clogs, rinse it in thinner and replace. To give a final finish, apply a small quantity of Com-Cut to the repair area. Take a clean cloth andstart with a soft rubbing action to restore shine. Wipe with a clean dry cloth.

Tips from com-Paint

Do not use the product if the surface is hot to touch. Only use light pressure on the emery pads to remove excess paint. Excessive pressure may remove the surrounding paint also. Use masking tape only, other type of tapes says "a cello-tape may cause paint damage on removal". Keep emery pads and paint surface wet while sanding.


Caution

Do not puncture, incinerate or store above 50° C. High temperature may cause Can bursting. Do not place Can on a radiator, stove, in direct sunlight or near other heat source. Use in well-ventilated area, in shade & between (18°C - 30°C) temperatures for best spray results. If spray gets into eyes flush with water. If swallowed, do not induce vomiting, call physician. Keep out of reach of children.